VMware VCENTER APPLICATION DISCOVERY MANAGER 6.1 - REPOSITORY Bedienungsanleitung Seite 201
- Seite / 220
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
OneCommand™ Manager Application P007997-01A Rev. B
13. Diagnostics
LightPulse FC HBA Diagnostics
201
Loopback Test Combinations
Run the following loopback test combinations using the appropriate checkboxes:
PCI Loopback Test – A firmware controlled diagnostic test in which a random
data pattern is routed through the PCI Bus without being sent to an adapter link
port. The returned data is subsequently validated for integrity.
Internal Loopback Test – A diagnostic test in which a random data pattern is
sent down to an adapter link port, then is immediately returned without
actually going out on the port. The returned data is subsequently validated for
integrity.
External Loopback Test – A diagnostic test in which a random data pattern is
sent down to an adapter link port. The data goes out the port and immediately
returns via a loopback connector. The returned data is subsequently validated
for integrity.
Note: You cannot run the External Loopback test and ECHO test concurrently. If you
select External Loopback the ECHO test section is disabled and vice versa.
Error Action
Enables you to define what is to be done in the event of a test failure. There are two
error action options:
Stop Test – Do not log the error and abort the test. No further tests are run.
Ignore – Log the error and proceed with the next test cycle.
Test Cycles
Enables you to specify test cycles three ways:
Select an established cycle count by clicking on the corresponding radio button.
Enter a custom cycle count in the blank field in the Test Cycles area.
Set the test to run until you manually click Stop Test, by selecting the Infinite
radio button.
Test Pattern
Enter a custom test pattern to be used in tests that transfer data. The test pattern can be
up to 8 hexadecimal bytes.
Test Status
The Test Status area displays how many completed cycles of each test ran, as well as the
number of errors.
To run loopback tests:
1. From the discovery-tree, select the adapter port on which you want to run the
Loopback Test.
- OneCommand™ Manager 1
- Application 1
- Version 6.1 1
- User Manual 1
- Table of Contents 3
- Table of Contents 4
- List of Figures 10
- List of Figures 11
- List of Tables 13
- 1. Introduction 14
- Compatibility 15
- Known Issues 16
- Abbreviations 16
- In Windows 18
- In Linux 20
- For RHEL 5 and RHEL 6 type: 21
- In Solaris 22
- In VMware ESX Server 24
- --maintenancemode update 25
- Web Launch Interface 26
- Installation 27
- Solaris: 28
- Linux: 28
- Web Launch Interface Only 29
- /opt/ELXocm/wsuninstall 30
- Manager Application 31
- Launch Interface 32
- Element Definitions 34
- Menu Bar 35
- Toolbar Buttons 35
- Discovery-Tree 37
- Property Tabs 38
- Status Bar 39
- Management Host 40
- 2. Run the following script: 41
- 5. Configuring Discovery 42
- Hosts File 43
- Adding a Single Host 45
- Adding a Range of Hosts 46
- Removing Hosts 48
- Adding Target Portals 52
- Removing a Target Portal 52
- Figure 5-7 iSCSI SNS Tab 53
- Logging into Targets 54
- Removing Targets 55
- Viewing Target Sessions 56
- Session Statistics Area 58
- Connection Information Area 59
- 7. Managing Hosts 61
- Function Summary Area 62
- Grouping Hosts 64
- Managing Host Groups 65
- Creating a Host Group 66
- Deleting a Host Group 66
- Adding a Host to a Host Group 67
- Restoring a Host Group 67
- Restoring all Host Groups 67
- Searching for Hosts 68
- Using CIM 69
- Viewing FC Port Information 71
- Viewing FCoE Port Information 73
- Figure 8-4 Statistics Tab 76
- Firmware Area 83
- WWN Management Area 84
- Mapping Information Area 87
- /usr/sbin/lpfc/lun_scan all 88
- LUN CapacityArea 89
- LUN Masking Area 89
- Current Settings Area 90
- Current Mappings Area 90
- Display Mode Radio Buttons 90
- Target Mapping Buttons 92
- Figure 8-14 LUN Masking Tab 93
- Changing Automapping Settings 95
- Adding a Persistent Binding 95
- Figure 8-18 Maintenance Tab 99
- Creating Virtual Ports 101
- 5x:xx:xx:xx:xx:xx:xx:xx 102
- 10:00:xx:xx:xx:xx:xx:xx 102
- 2x:xx:xx:xx:xx:xx:xx:xx 102
- 3x:xx:xx:xx:xx:xx:xx:xx 102
- Deleting Virtual Ports 103
- Figure 8-22 Virtual Port Tab 104
- Figure 8-24 Reset Warning 107
- Activation Requirements 108
- Setting Driver Parameters 110
- Resetting All Default Values 112
- Parameter Value 112
- DCB Settings Area 118
- CIN Settings Area 119
- DCB Tab Field Definitions 120
- Viewing iSCSI VPD Information 126
- Viewing iSCSI Statistics 127
- Viewing iSCSI LUN Information 131
- Viewing iSCSI PCI Registers 133
- DCBX Settings Area 136
- LLDP Settings Area 137
- PFC Priorities Area 137
- ETS Priority Groups Area 137
- Advanced TCP/IP Configuration 140
- Initiator Login Options Area 142
- Authentication Area 142
- Viewing NIC Port Information 144
- Viewing NIC VPD Information 146
- VPD Table Definitions 147
- Base Host Operating System 153
- Guest Host Information Area 154
- Operating System 155
- OneConnect Adapters 156
- Viewing ASIC Information 158
- Personality Area 160
- License Features Area 160
- Showing Licenses 162
- Installing Licenses 163
- Boot Code Versions Area 166
- PHY Data Field Definitions 169
- Error Rates Area 170
- Counters Area 170
- Module Attributes Area 171
- Diagnostic Data Area 172
- Linux Considerations 173
- Enabling Authentication 173
- DHCHAP Tab 175
- Changing Your Password 177
- 10. Updating Adapter Firmware 178
- Boot Types 183
- Boot Device Parameters 184
- 100 ms 191
- 200 ms 191
- 12. Exporting SAN Information 193
- 13. Diagnostics 194
- Information 195
- Viewing Flash Contents 195
- Viewing Overlay Details 196
- Viewing the PCI Registers 196
- Running a Quick Test 196
- Using Beaconing 197
- Creating Diagnostic Dumps 198
- LightPulse FC HBA Diagnostics 199
- Running Loopback Tests 200
- Loopback Test Combinations 201
- Saving the Log File 203
- OneConnect Diagnostics 204
- FCoE End to End Echo Test 206
- Error Action 206
- Test Cycles 206
- Test Pattern 206
- Test Status 206
- 14. Troubleshooting 211
- Situation Resolution 212
- Application Situations 214
- ./stop_ocmanager 215
- Situations 219
Verwandte Produkte und Handbücher für Software VMware VCENTER APPLICATION DISCOVERY MANAGER 6.1 - REPOSITORY
(46 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern