VMware VCENTER APPLICATION DISCOVERY MANAGER 6.1 - REPOSITORY Bedienungsanleitung Seite 189
- Seite / 220
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
OneCommand™ Manager Application P007997-01A Rev. B
11. Configuring Boot from an FC SAN
Configuring Advanced Settings (Boot from SAN)
189
x86 Boot Advanced Adapter Settings Definitions
Enable Start unit command – Issues the SCSI start unit command. You must
know the specific LUN to issue.
Enable EDD 3.0 – Enables the Enhanced Disk Drive (EDD) option (shows the
path to the boot device). Available on Intel Itanium servers only.
Note: An x86 series system could hang during Windows 2000 Server
installation if EDD 3.0 is enabled.
Enable spinup delay – If at least one boot device has been defined, and the
spinup delay is enabled, the BIOS searches for the first available boot device.
If a boot device is present, the BIOS boots from it immediately.
If a boot device is not ready, the BIOS waits for the spinup delay and, for up
to three additional minutes, continues the boot scanning algorithm to find
another multi-boot device.
Note: The default topology is auto topology with loop first. Change this
topology setting, if necessary, before configuring boot devices.
If no boot devices have been defined and auto scan is enabled, then the BIOS
waits for five minutes before scanning for devices.
In a private loop, the BIOS attempts to boot from the lowest target AL_PA it
finds.
In an attached fabric, the BIOS attempts to boot from the first target found in
the NameServer data.
Enable environment variable – Sets the boot controller order if the system
supports the environment variable.
Enable auto boot sector – Automatically defines the boot sector of the target
disk for the migration boot process, which applies only to HP MSA1000 arrays.
If there is no partition on the target, the default boot sector format is 63 sectors.
Set Auto Scan – With auto scan enabled, the first device issues a Name Server
Inquiry. The boot device is the first DID, LUN 0, or not LUN 0 device returned,
depending on the option you select. Only this device is the boot device and it is
the only device exported to the Multi-boot menu. Auto Scan is available only if
none of the eight boot entries is configured to boot via DID or WWPN. Emulex
strongly recommends that you use the Configure Boot Devices menu to
configure eight boot entries for fabric point-to-point, public loop or private loop
configurations. Set to one of the following:
Disabled (default)
Any First Device
First LUN 0 Device
First non-LUN 0 Device
Set the PLOGI Retry Timer – Sets the interval for the PLOGI (port log in) retry
timer. This option is especially useful for Tachyon-based RAID arrays. Under
very rare occasions, a Tachyon-based RAID array resets itself and the port goes
offline temporarily in the loop. When the port comes to life, the PLOGI retry
- OneCommand™ Manager 1
- Application 1
- Version 6.1 1
- User Manual 1
- Table of Contents 3
- Table of Contents 4
- List of Figures 10
- List of Figures 11
- List of Tables 13
- 1. Introduction 14
- Compatibility 15
- Known Issues 16
- Abbreviations 16
- In Windows 18
- In Linux 20
- For RHEL 5 and RHEL 6 type: 21
- In Solaris 22
- In VMware ESX Server 24
- --maintenancemode update 25
- Web Launch Interface 26
- Installation 27
- Solaris: 28
- Linux: 28
- Web Launch Interface Only 29
- /opt/ELXocm/wsuninstall 30
- Manager Application 31
- Launch Interface 32
- Element Definitions 34
- Menu Bar 35
- Toolbar Buttons 35
- Discovery-Tree 37
- Property Tabs 38
- Status Bar 39
- Management Host 40
- 2. Run the following script: 41
- 5. Configuring Discovery 42
- Hosts File 43
- Adding a Single Host 45
- Adding a Range of Hosts 46
- Removing Hosts 48
- Adding Target Portals 52
- Removing a Target Portal 52
- Figure 5-7 iSCSI SNS Tab 53
- Logging into Targets 54
- Removing Targets 55
- Viewing Target Sessions 56
- Session Statistics Area 58
- Connection Information Area 59
- 7. Managing Hosts 61
- Function Summary Area 62
- Grouping Hosts 64
- Managing Host Groups 65
- Creating a Host Group 66
- Deleting a Host Group 66
- Adding a Host to a Host Group 67
- Restoring a Host Group 67
- Restoring all Host Groups 67
- Searching for Hosts 68
- Using CIM 69
- Viewing FC Port Information 71
- Viewing FCoE Port Information 73
- Figure 8-4 Statistics Tab 76
- Firmware Area 83
- WWN Management Area 84
- Mapping Information Area 87
- /usr/sbin/lpfc/lun_scan all 88
- LUN CapacityArea 89
- LUN Masking Area 89
- Current Settings Area 90
- Current Mappings Area 90
- Display Mode Radio Buttons 90
- Target Mapping Buttons 92
- Figure 8-14 LUN Masking Tab 93
- Changing Automapping Settings 95
- Adding a Persistent Binding 95
- Figure 8-18 Maintenance Tab 99
- Creating Virtual Ports 101
- 5x:xx:xx:xx:xx:xx:xx:xx 102
- 10:00:xx:xx:xx:xx:xx:xx 102
- 2x:xx:xx:xx:xx:xx:xx:xx 102
- 3x:xx:xx:xx:xx:xx:xx:xx 102
- Deleting Virtual Ports 103
- Figure 8-22 Virtual Port Tab 104
- Figure 8-24 Reset Warning 107
- Activation Requirements 108
- Setting Driver Parameters 110
- Resetting All Default Values 112
- Parameter Value 112
- DCB Settings Area 118
- CIN Settings Area 119
- DCB Tab Field Definitions 120
- Viewing iSCSI VPD Information 126
- Viewing iSCSI Statistics 127
- Viewing iSCSI LUN Information 131
- Viewing iSCSI PCI Registers 133
- DCBX Settings Area 136
- LLDP Settings Area 137
- PFC Priorities Area 137
- ETS Priority Groups Area 137
- Advanced TCP/IP Configuration 140
- Initiator Login Options Area 142
- Authentication Area 142
- Viewing NIC Port Information 144
- Viewing NIC VPD Information 146
- VPD Table Definitions 147
- Base Host Operating System 153
- Guest Host Information Area 154
- Operating System 155
- OneConnect Adapters 156
- Viewing ASIC Information 158
- Personality Area 160
- License Features Area 160
- Showing Licenses 162
- Installing Licenses 163
- Boot Code Versions Area 166
- PHY Data Field Definitions 169
- Error Rates Area 170
- Counters Area 170
- Module Attributes Area 171
- Diagnostic Data Area 172
- Linux Considerations 173
- Enabling Authentication 173
- DHCHAP Tab 175
- Changing Your Password 177
- 10. Updating Adapter Firmware 178
- Boot Types 183
- Boot Device Parameters 184
- 100 ms 191
- 200 ms 191
- 12. Exporting SAN Information 193
- 13. Diagnostics 194
- Information 195
- Viewing Flash Contents 195
- Viewing Overlay Details 196
- Viewing the PCI Registers 196
- Running a Quick Test 196
- Using Beaconing 197
- Creating Diagnostic Dumps 198
- LightPulse FC HBA Diagnostics 199
- Running Loopback Tests 200
- Loopback Test Combinations 201
- Saving the Log File 203
- OneConnect Diagnostics 204
- FCoE End to End Echo Test 206
- Error Action 206
- Test Cycles 206
- Test Pattern 206
- Test Status 206
- 14. Troubleshooting 211
- Situation Resolution 212
- Application Situations 214
- ./stop_ocmanager 215
- Situations 219
Verwandte Produkte und Handbücher für Software VMware VCENTER APPLICATION DISCOVERY MANAGER 6.1 - REPOSITORY
(46 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern